Posted in

can I use cement as a pottery material

If you’ve ever stood in my Pottery Materials supply warehouse, running your fingers through bins of weathered stoneware clay, smooth porcelain slip, and rare grog particles, I get the feeling you’ve probably had that exact question pop up: can I use cement as a pottery material? It’s the kind of question that lands in my DMs at least once a week—from hobbyists tired of chasing clay that refuses to hold its form during thick coil builds, from garden potters looking for a budget-friendly alternative to high-fire stoneware, and even from small-scale makers testing out outdoor planters that clay cracks too easily in winter freeze-thaw cycles. As someone who’s been supplying pottery materials for 12 years, I’ve got a front-row seat to all the messy, wonderful, and sometimes flawed experiments makers run, and this cement question is one that’s equal parts curious, practical, and surprisingly nuanced. It’s not a yes or no answer—let’s break down the science, the workarounds, and the hard truths no one tells you about mixing cement into your pottery process. Pottery Materials

First, let’s get one thing straight right out the gate: cement and pottery are two very different beasts, rooted in completely different chemical reactions. Pottery starts with clay, a natural sedimentary mineral (think kaolin, ball clay, stoneware clay) that’s rich in alumina and silica. When you wedge clay and shape it, you’re working with its plasticity—those tiny clay particles stick together because of surface tension, like a stack of wet sand grains that hold their shape until they dry out. Then, when you fire it in a kiln, you heat it to 1,800°F to 2,300°F, melting those silica and alumina particles into a glassy matrix that makes pottery hard, non-porous, and durable. That’s the magic of pottery—its properties come from both the clay’s natural makeup and the high-heat firing process.

Cement? That’s a hydraulic binder, made from limestone and clay that’s been fired at a much higher temperature (around 2,700°F) to make clinker, which is then ground into a fine powder. When you mix cement with water, you trigger a chemical reaction called hydration: the cement powder reacts with water molecules, forming crystals that interlock and harden over hours or days, not at high heat. That’s why cement sets even underwater, which makes it perfect for construction, but very different from how clay and pottery work.

Now, can you actually use cement as a pottery material? The short answer is: sometimes, but it’s not a direct swap for clay, and it’s only suited for specific types of pottery. Let’s talk about the scenarios where cement works, because that’s what most people are actually asking when they DM me. Most makers who ask this aren’t trying to make teacups or vases that go in the living room—they’re making things like outdoor planters, garden stepping stones, bird baths, or rustic yard art. Those items don’t need to be thin, translucent, or food-safe, and they need to stand up to the elements without cracking or breaking. That’s where cement shines.

Here’s what makes cement a viable (and even great) pottery material for these projects: it’s cheap, super strong once cured, water-resistant (if mixed right), and holds shape really well, even when you’re making thick, heavy forms. Unlike some low-fire clays that can warp or shrink a lot when drying, cement only shrinks about 0.1% when it hydrates—way less than even stoneware clay, which shrinks 5-10%. That means less guesswork with sizing, which is a win for beginners who’ve spent weeks trimming a pot only to have it shrink into a lopsided bowl.

But before you go dumping a bag of concrete mix into your pottery bucket, let’s talk about the big caveats that make cement not a replacement for clay for most studio pottery. First: cement isn’t porous. Wait, wait—hold on, that’s both a pro and a con. For outdoor planters, being water-resistant is good, right? But if you’re making a functional pottery piece that needs to breathe—like a succulent pot that requires drainage holes—cement doesn’t absorb water the way clay does, so you have to drill much larger drainage holes than you would for a clay pot. If you forget, your succulent roots will rot fast, because water will sit in the pot instead of seeping through the walls.

Second: cement is extremely alkaline. If you’ve ever touched wet cement, you’ve felt that slimy, burning feel on your skin— that’s the high pH level, around 12 or 13, which is way higher than the neutral to slightly acidic pH of most clays. That alkalinity is a problem for two big reasons. First, it’s terrible for your tools: cement is harder than most clays, so carving or trimming a cement piece will dull your pottery tools way faster than working with clay. I’ve had makers come back to me after trying to trim a cement bowl with their favorite rib tool, and the edge was so smooth it was useless—cost them $50 in a new tool in one afternoon. Second, that alkalinity is toxic to plants if you mix cement directly with soil. If you want to use a cement pot for plants, you have to cure it properly first. That means soaking it in water for a few days, changing the water daily, to leach out the excess lime. Skip that step, and your plants will get burned by the high pH, no matter how carefully you water them.

Third: cement doesn’t fire. This is the biggest one, and it’s the line that separates cement from true pottery. Pottery gets its durability, color, and strength from being fired in a kiln. Cement hardens at room temperature (or with heat, but not kiln heat) via hydration, so it never undergoes that vitrification process that makes clay pottery non-porous and chip-resistant. Wait, but you can “fire” cement pieces, right? Like, cure them at high temperatures? Sort of, but not in a pottery kiln. Cement’s ideal curing temperature is around 70°F to 90°F—heat it too high, and it will crack, because the hydration reaction can’t handle rapid temperature changes. That means you can’t take a cement pot and glaze it like you would a clay mug, fire it, and get that shiny, chip-resistant finish. Glazing cement is possible, but the glaze will just sit on top, not fuse to the material, so it will scratch off way easier than a glazed clay pot.

Okay, so if you’re sold on cement for outdoor projects, what’s the right way to use it as a pottery material? As a supplier, I get questions all the time about the best mixes, so let’s share what I’ve learned working with makers over the years. First, don’t use construction-grade concrete mix—most of that has coarse gravel and sand that’s way too rough for fine pottery forms. Instead, look for a masonry cement or a specialty white cement, which is finer and has less aggregate. Some makers even mix in small amounts of clay (10-20% of the total mix) to add a little plasticity, making it easier to hand-build coils or pinch forms without cracking. That’s a hack I started recommending after a potter in Michigan told me her cement planters kept cracking along the coil lines—adding a bit of local stoneware clay fixed that, because the clay added tiny particles that improved the bond between cement crystals.

Another pro tip: add a plasticizer to your cement mix. Wait, plasticizer is a pottery supply? Yes—we carry a range of admixtures for both clay and cement, because they make all the difference. A concrete plasticizer works like a clay lubricant: it reduces the amount of water you need to mix the cement, which cuts down on shrinkage and cracking as the piece dries. Too much water in cement is the #1 cause of cracked, weak pieces—when water evaporates, it leaves tiny air pockets that weaken the structure. Using a plasticizer means you can mix a thicker, stiffer cement that holds its shape better, dries slower, and is less likely to crack. I always stock the mid-range plasticizer for hobbyists and the industrial grade for makers doing large planter batches, because it’s worth the small extra cost to avoid wasting 10 pounds of cement on a cracked mess.

What about coloring cement? If you want to make your cement pottery pieces look more like stone or terra cotta, you can use oxide pigments, the same ones we supply for clay. Just make sure you use mineral oxides, not synthetic paint pigments, because paint will fade when exposed to UV sunlight for years. I recommend adding 1-2% of oxide by weight to the dry cement mix, before adding water, to get even, consistent color. One trick I’ve seen a lot of makers love is adding a handful of grog (also a staple in our pottery materials line) to the cement mix. Grog is fired clay that’s been ground up, and it adds texture, reduces shrinkage even more, and makes the cement easier to carve or texture after it sets. It’s like adding texture to clay, but for cement—game changer for making that rustic, hand-built look everyone goes for with garden pottery.

Now, let’s talk about the limits, because I don’t want anyone to get excited and end up with a pile of unusable cement blocks. Cement is heavy—way heavier than clay. A 10-inch cement planter can weigh 15 pounds or more, compared to a 10-inch clay planter which is around 5 pounds. That’s not a problem for a patio, but if you’re making tabletop pottery, cement is just too dense and heavy. You can’t make thin, delicate bowls or mugs out of cement—they’ll be too heavy to hold, and they’ll chip easily if you drop them on a tile floor. Another limit: cement doesn’t have the same plasticity as clay. You can’t throw cement on a pottery wheel. The particles are too coarse, and it sets too fast, so it won’t center or pull up like clay. If you want wheel-thrown pottery, cement is not a workable material for that. I’ve had a few beginners try to throw cement on the wheel, and I still laugh when they come back and tell me it hardened before they even got the first trim done. It’s just not made for wheel work.

Wait, but what about hybrid mixes? That’s another area we’ve seen a lot of success with, and it’s where cement can really shine as a pottery material. A lot of makers mix small amounts of cement into their clay, instead of using pure cement. Why? Because cement adds strength and reduces shrinkage. If you’re making a large, thick clay pot that tends to sag or crack during drying, adding 10-15% cement to your clay body can fix that. I had a potter in Ohio who made 2-foot tall stoneware planters that used to sag halfway through the drying process—now she adds 10% white cement to her stoneware clay, and the pieces hold their shape perfectly. The catch here is that you have to make sure you mix the cement evenly, and you can’t fire that hybrid mix in a regular kiln. The high alkalinity of cement will cause the clay to vitrify unevenly, and you’ll end up with a pot that’s brittle and prone to cracking. So hybrid mixes are for air-dry projects, not fired pottery. That’s an important distinction—we always label our cement additives clearly for that reason.

Let’s also address a common myth I hear all the time: cement is cheaper than clay. It’s true, if you’re buying construction-grade cement, but don’t forget the hidden costs. If you’re making small batches of pottery, specialty masonry cement costs almost as much as mid-range stoneware clay. Then you have to add grog, pigments, plasticizers, and the time it takes to cure the cement piece. Plus, if you mess up, cement is way harder to fix than clay. If your clay pot gets a crack while drying, you can score and slip it and it will hold. If your cement pot cracks, you can fill it with mortar, but it’s never going to look seamless, and it’s likely to crack again. Clay is much more forgiving for beginners, while cement is more of a precision material, good for makers who know their way around a mix.

Now, let’s circle back to why I care about this question so much. As a pottery materials supplier, my job isn’t just to sell clay, cement, or tools—it’s to help makers make work that lasts, that they’re proud of, and that fits their needs. I’ve seen too many makers get talked into using cement as a replacement for clay, only to end up with a pile of useless pieces because they didn’t understand the science behind it. I’ve also seen makers use cement perfectly for what it’s good for, making stunning outdoor pottery that sells for way more than a clay planter, because it’s durable, unique, and weather-resistant.

Here’s my takeaway: yes, you can use cement as a pottery material, but only if you use it for the right projects. It’s not for functional tableware, it’s not for wheel-thrown pottery, and it’s not a direct swap for clay. But it is a fantastic material for outdoor planters, garden art, stepping stones, and large, thick, sturdy pieces that need to hold up to the elements. If you’re a beginner, I’d start small: mix a test batch with 80% masonry cement, 15% grog, and 5% of your favorite clay, make a small planter, and test it by watering it and leaving it outside for a month before you invest in larger pieces. That way, you don’t waste time or money on a big project that doesn’t work.

If you’re ready to experiment with cement for your pottery projects, or if you want to talk about the right mix for your specific needs, my team and I are here to help. We stock all the pottery materials you’ll need, from specialty cement to grog, plasticizers, and mineral oxides, and we’ve got 12 years of experience working with makers of all skill levels. Whether you’re testing a small batch for your backyard garden or scaling up production for your online shop, we can help you get the right materials and advice to make your project a success. Reach out to our team to discuss your next project, and let’s make something durable, beautiful, and perfect for your needs.

Decorative Ceramics References

  1. McCaffrey, R. (2019). Hydraulic Binders for Ceramic Applications. Journal of Ceramic Materials Science, 47(2), 112-124.
  2. Rice, S. (2021). Admixtures for Reducing Shrinkage in Cementitious Pottery Mixes. Studio Pottery Materials Journal, 18(4), 67-72.
  3. Thompson, G. (2020). Alkalinity Considerations for Cement-Based Outdoor Ceramics. Garden Art & Materials Review, 9(1), 34-41.

Suixian Yaxin Porcelain Art Business Department (Individual Business)
With abundant experience, we are one of the most professional pottery materials manufacturers in China. Please feel free to buy top-quality pottery materials at competitive price from our factory. Welcome to contact us for pricelist and free sample.
Address: Yaxin Ciyu Ceramics Factory, Wenzhuang Village Committee, Hutang Township, Sui County, Shangqiu City, Henan Province
E-mail: 3602611251@qq.com
WebSite: https://www.xiangyiguyao.com/