If you’re a farm owner, landscaper, or even someone who uses a knapsack power sprayer for occasional weed control or pest treatments, you know these tools aren’t cheap. I sell knapsack sprayers for a living, and I can’t tell you how many times customers come to me in spring, panicking because their sprayer won’t start after sitting idle all winter. That’s not just a hassle—it’s a waste of money, and trust me, it’s totally avoidable. Storing a knapsack power sprayer long term isn’t just shoving it in a corner of the shed and forgetting about it. Skip the lazy moves, and you’ll save yourself from buying a new one every couple of years. Knapsack Power Sprayer

First, let’s cut to the chase: what even counts as “long term” for a sprayer? I’m talking more than a month, usually the off-season—like 3+ months, no use at all. Whether you’re wrapping up pest control for the fall, putting weed spray on hold until next spring, or taking a break after a big job, the steps are the same. Mess these up, and you’re dealing with clogged nozzles, rusted engines, dried-out hoses, or even cracked plastic tanks when you pull it back out. I’ve seen it all, from a customer’s sprayer that seized up because they left gas in the tank over winter, to another where the hose turned brittle and snapped when they tried to squeeze the trigger. Don’t be that guy.
Let’s start with the most common mistake people make: leaving fuel in the engine and tank. I get it—you’re tired after a long day spraying, you just want to pack up and go inside. But gasoline breaks down fast, especially in small engines like the ones on our knapsack sprayers. Old gas turns gummy, and that gunk clogs carburetors, fuel lines, and nozzles. I’ve had customers bring in sprayers with carburetors so gummed up, we have to take them apart, clean every part, and sometimes even replace the whole thing. That’s a $50-$100 repair, just because they didn’t drain the gas.
So step one for long-term storage: drain every drop of gas. Here’s how to do it right, not just the messy “pour it out on the ground” way (side note: that’s bad for the environment, don’t do that). First, start the engine and let it run until it dies on its own—that will burn up any gas left in the lines and carburetor. That’s a quick fix for the inner parts. Then, for the tank, you have to empty it completely. Some sprayers have a drain plug at the bottom of the fuel tank, just unscrew that and let all the gas flow into a approved container. If yours doesn’t have a drain plug, you can use a siphon pump, which is cheap and works way better than trying to tilt the sprayer (and spill half the gas on your shoes). Once the tank is empty, let it sit for a minute to make sure no leftover gas is sitting in the lines.
Wait—what if you have a 2-stroke engine? Those use gas and oil mixed, right? Same rule applies. Drain the mix completely, no exceptions. I know it’s a bit of a pain to mix new gas and oil when you’re ready to use it again, but it’s way better than dealing with a clogged carburetor. Some people try to add a fuel stabilizer instead of draining, but here’s the thing: stabilizer works for short term (a month or two), but long term (3+ months) it’s risky. Even with stabilizer, gas will still break down eventually, and you’re leaving that gummy residue in your engine. Save the stabilizer for quick stashes, not long-term storage.
Next up: what’s inside the sprayer tank? If you used it for herbicides, pesticides, or any kind of liquid fertilizer, you can’t just leave that in there either. Those chemicals are corrosive, and even small amounts can eat away at the plastic tank, hoses, or seals over time. I’ve had a customer come to me last year with a tank that had a tiny hole corroded in it, all because they left weed killer in it over the winter. Total bummer, and totally preventable.
So step two: clean the tank thoroughly. Here’s my go-to method, works every time. First, dump out whatever liquid is left in the tank—don’t pour it down the drain, take it to a local hazardous waste facility or a shop that accepts old chemicals, they can dispose of it properly. Then, fill the tank with warm water, add a squirt of mild dish soap (not a strong cleaner, that can leave residue), and put the lid back on. Take the sprayer off your back, prop it up so the lid is tight, and shake it really well—like, really shake it. If it’s a bigger sprayer, you can even let the soapy water sit in there for 15-20 minutes to break up any stuck gunk. Then, drain the soapy water, and rinse the tank at least two times with clean water to make sure all the soap is gone.
Don’t forget the nozzles and hoses! Those are super easy to skip, but they’re the parts that actually do the spraying. If you leave liquid in the nozzle, it can dry up and clog it, so you can’t get a good spray when you need it. After you rinse the tank, remove the nozzles, soak them in warm soapy water for 10 minutes, then use a soft brush (like an old toothbrush) to clean out any gunk. If they’re really clogged, you can use a small pin to gently poke the hole (just don’t make it bigger, that’ll make the spray go all over the place). For the hoses, flush them with clean water too—attach a hose to the inlet, run water through until it comes out the nozzle, then let the hoses hang out to dry completely. Moisture is the enemy here, it causes rust and mold.
Now, the engine parts we talked about earlier—we drained the gas, but what about the carburetor, the air filter, and the spark plug? Let’s knock those out. The air filter can get clogged with dust and dirt over time, and if you leave it dirty, that dirt can get into the engine and cause wear. Take it out, clean it with compressed air (if you don’t have a compressor, you can blow on it hard, just don’t spit in it) or wash it with mild soap and water, let it dry completely, then put it back. If it’s really worn out, go ahead and replace it—they’re cheap, like $5-$10, and way easier than fixing a worn engine later.
For the spark plug: remove it, check if it’s dirty or corroded. If it’s just a little dirty, you can clean it with a wire brush, but if it’s worn (the gap is too big), replace it. Then, a quick trick to keep the engine from rusting: pour a teaspoon of clean engine oil into the spark plug hole, pull the starter cord a few times to spread the oil around the cylinder, then put the spark plug back in (don’t connect the wire yet). That forms a thin protective layer on the metal parts, so they don’t rust while stored.
Okay, now the tank is cleaned, the engine is prepped, the nozzles are clean—what next? Drying everything is non-negotiable. I know, I know, it sounds like a hassle, but if you put a damp sprayer in a plastic bag or a closed shed, you’re asking for mold, mildew, and rust. Let all parts air dry completely. Take the hoses, hang them up in a cool, dry place—don’t just coil them up and throw them in a pile. Coiling hoses while they’re damp can make them stick together, and over time, that can cause cracks. Hang them loosely, so there’s no kinks, and let them dry for at least a full day. The tank and the engine parts too—wipe them down with a dry cloth, make sure there’s no moisture left anywhere.
Wait, what about the backpack straps and the frame? Those are easy to forget. If they’re made of fabric (some of our sprayers have padded straps), wipe them down with a damp cloth, then let them dry completely. If they’re plastic or metal, wipe them down too. Don’t leave sweat or dirt on the straps for months, that can make the fabric moldy or the metal rust.
Now, where to store it? Location matters more than you think. Don’t leave your sprayer outside, even under a tarp. Sunlight can break down the plastic and rubber parts, making them brittle. Rain or dew will get in, causing rust. The best spot is a cool, dry, well-ventilated place—like a shed, a garage, or a closet in the house. The temperature shouldn’t swing too much, so don’t store it next to a heater or a window that gets direct sun. If you have to put it in a spot that gets a little damp, you can put it on a shelf or a wooden pallet, so it’s not sitting on the floor where moisture can seep up.
When you put it in storage, how should you arrange it? Don’t lean it on its side or upside down for months. That can push oil and gas into places they don’t belong, or even crack the tank if it’s plastic. Stand it upright, or prop it up so it’s balanced on its base. If you want to wrap it to keep dust off, use a breathable cover—like a cotton sheet, not a plastic bag. Plastic traps moisture, which is exactly what we don’t want. A cotton sheet lets air circulate, so no mold grows.
Let me test if this makes sense with an example. Last winter, a customer bought a knapsack sprayer from me and followed all these steps. When he pulled it out in March, it started on the first pull, no clogged nozzles, no rust. Another customer last year skipped draining the gas, left weed killer in the tank, and stored it in his unheated shed. When he pulled it out, the carburetor was gummed up, the tank had a tiny hole, and the hose was brittle. He had to buy a new sprayer, which cost way more than if he’d taken the 30 minutes to do the right storage steps.
Wait, are there any exceptions? Let’s say you’re storing it for less than 3 months—like a month, after a big job. You can get away with a fuel stabilizer, just make sure you run the engine for 5 minutes after adding it to circulate it through the carburetor. But if it’s going to be more than 3 months, drain the gas, no questions. Also, if you used the sprayer for something like fertilizer, which is less corrosive than herbicides, you still have to clean the tank—just because it’s milder doesn’t mean it won’t cause damage over time.
Another pro tip: label everything. When you put your sprayer in storage, take a Sharpie and write the date on the tank. That way, next year, you’ll remember how long it’s been stored, and you’ll know if you need to do extra checks before using it. Also, if you keep extra parts (nozzles, hoses, air filters) with the sprayer, write that down too, so you don’t lose them.

Now, let’s talk about what NOT to do. Don’t use old gas that’s been sitting in a can for more than 6 months—even in a sealed can, gas breaks down. Don’t use strong chemicals like bleach to clean the tank, that can leave a residue that mixes with your next spray and ruins it. Don’t store the sprayer near pesticides or other harsh chemicals, because fumes can get into the tank and damage the seals.
Gasoline Power Duster At the end of the day, storing your knapsack power sprayer long term is all about taking those extra 30 minutes instead of cutting corners. I’ve built my business on selling reliable sprayers, and I hate seeing customers waste their money because of a lazy storage job. If you’re in the market for a new sprayer, or you have questions about maintaining the one you have, feel free to reach out to our team for help. We’re here to make sure your sprayer lasts as long as it should, so you don’t have to stress about it when you need it most.
References
- Small Engine Maintenance Guide, National Agricultural Library, U.S. Department of Agriculture
- Pesticide Container Storage and Cleaning Best Practices, Environmental Protection Agency
- Knapsack Sprayer Long-Term Storage Manual, Agricultural Equipment Manufacturers Association
- Rust Prevention for Small Engine Components, Society of Automotive Engineers
Taizhou Tianyi Agriculture & Forestry Machinery Co., Ltd.
As one of the most professional knapsack power sprayer manufacturers and suppliers in China, our products have good reputation in the market. Please rest assured to wholesale customized knapsack power sprayer made in China here from our factory. If you have any enquiry about quotation, please feel free to email us.
Address: 2988 Binkang Avenue, Taizhou Bay New District, Taizhou, Zhejiang, China
E-mail: info@cnsprayers.com
WebSite: https://www.cnsprayers.com/